Model 607A61 Product Type: Accelerometer Low-profile industrial ICP® accelerometer, side exit, armored jacketed cable and swiveler base View  photo .
PERFORMANCE ENGLISH SI Sensitivity  (± 15 %) 100 mV/g 10.2 mV/(m/s²) [2] Measurement Range ± 50 g ± 490 m/s² Frequency Range  (± 3 dB) 30 to 600000 cpm 0.5 to 10,000 Hz Resonant Frequency 1500 kcpm 25 kHz [1] Broadband Resolution  (1 to 10,000 Hz) 350 mg 3434 mm/s² [1] Non-Linearity ± 1 % ± 1 % [3] Transverse Sensitivity £ 7 % £ 7 % ENVIRONMENTAL     Overload Limit  (Shock) 5000 g pk 49,050 m/s² pk Temperature Range -65 to +250 °F -54 to +121 °C Temperature Response See Graph See Graph Enclosure Rating IP67 IP67 ELECTRICAL     Settling Time  (within 1% of bias) £ 2 sec £ 2 sec Discharge Time Constant ³ 0.3 sec ³ 0.3 sec Excitation Voltage 18 to 28 VDC 18 to 28 VDC Constant Current Excitation 2 to 20 mA 2 to 20 mA Output Impedance <150 ohms <150 ohms Output Bias Voltage 8 to 12 VDC 8 to 12 VDC Spectral Noise  (10 Hz) 8 mg/ÖHz 78.5 (mm/s²)/ÖHz [1] Spectral Noise  (100 Hz) 5 mg/ÖHz 49.1 (mm/s²)/ÖHz [1] Spectral Noise  (1 kHz) 4 mg/ÖHz 39.2 (mm/s²)/ÖHz [1] Electrical Isolation  (Case) >108 ohms >108 ohms PHYSICAL     Size (Hex x Height) 9/16 in x 1.0 in 14 mm x 25.4 mm Weight  (without cable) 1.1 oz 31 gm [4] Mounting Stud Stud Mounting Thread 1/4-28 Male Not Applicable [5] Mounting Torque  (stud) 7 to 8 ft-lb 9.5 to 10.8 N-m [6][7] Mounting Torque  (hex nut) 2 to 5 ft-lb 2.7 to 6.8 N-m Sensing Element Ceramic Ceramic Sensing Geometry Shear Shear Housing Material Stainless Steel Stainless Steel Sealing Welded Hermetic Welded Hermetic Electrical Connector Armor Jacketed Cable Armor Jacketed Cable Electrical Connection Position Side Side Cable Length 10 ft 3.0 m Cable Type Polyurethane Polyurethane [8] SUPPLIED ACCESSORIES: Model 080A156 Mounting Base (1) Model ICS-2 NIST-traceable single-axis single-point amplitude response calibration at 6000 cpm (100 Hz) OPTIONAL VERSIONS CS - Canadian Standards Association Approved Intrinsically Safe [10] M - Metric Mount Supplied Accessory : Model M080A159 Mounting stud, 1/2-20 to M6x1 (for Models M607A11and M607A61) (1) replaces Model 080A156 TO - Temperature Output Temperature Output Range +36 to +250 °F +2 to +121 °C Temperature Scale Factor 5.56 mV/°F + 32 +10 mV/°C Electrical Connector Armor Jacketed Cable Armor Jacketed Cable Electrical Connections (Red) Acceleration Output Acceleration Output Electrical Connections (Black) Ground Ground Electrical Connections (White) Temperature Output Temperature Output All specifications are at room temperature unless otherwise specified. NOTES: [1] Typical. [2] Conversion Factor 1g = 9.81 m/s². [3] Zero-based, least-squares, straight line method. [4] Measured with mounting stud. [5] 1/4-28 has no equivalent in S.I. units. [6] 1/8" hex Allen key required for English version, 4 mm hex Allen key required for Metric version. [7] Stud torque must exceed sensor hex nut torque to ensure proper dismantling. [8] Stainless steel armor jacket over twisted shielded pair. [9] See PCB Declaration of Conformance PS023 for details. [10] Division 1; Class I; Group A, B, C & D; Temperature Code T4. [9]