Model 625B62 Product Type: Accelerometer Ring-shaped, industrial, ceramic shear ICP® accel., 500 mV/g, 0.2 to 6000 Hz, side exit, 10 ft integral armor cable View  photo .
PERFORMANCE ENGLISH SI Sensitivity  (± 5 %) 500 mV/g 51 mV/(m/s²) [2] Measurement Range ± 10 g ± 98 m/s² Frequency Range  (± 5 %) 30 to 120000 cpm 0.5 to 2000 Hz [3] Frequency Range  (± 10 %) 22 to 240000 cpm 0.37 to 4000 Hz Frequency Range  (± 3 dB) 12 to 360000 cpm 0.2 to 6000 Hz Resonant Frequency 720 kcpm 12 kHz [1] Broadband Resolution  (1 to 10,000 Hz) 15 mg 147 mm/s² [1] Non-Linearity ± 1 % ± 1 % [4] Transverse Sensitivity £ 7 % £ 7 % ENVIRONMENTAL     Overload Limit  (Shock) 2500 g pk 24,525 m/s² pk Temperature Range -65 to +250 °F -54 to +121 °C Temperature Response See Graph See Graph Enclosure Rating IP68 IP68 ELECTRICAL     Settling Time  (within 1% of bias) £ 4.5 sec £ 4.5 sec Discharge Time Constant ³ 1.0 sec ³ 1.0 sec Excitation Voltage 18 to 28 VDC 18 to 28 VDC Constant Current Excitation 2 to 20 mA 2 to 20 mA Output Impedance <100 ohms <100 ohms Output Bias Voltage 8 to 12 VDC 8 to 12 VDC Spectral Noise  (10 Hz) 0.9 mg/ÖHz 8.8 (mm/s²)/ÖHz [1] Spectral Noise  (100 Hz) 0.7 mg/ÖHz 7.0 (mm/s²)/ÖHz [1] Spectral Noise  (1 kHz) 0.3 mg/ÖHz 3.1 (mm/s²)/ÖHz [1] Electrical Isolation  (Case) >108 ohms >108 ohms Electrical Protection RFI/ESD RFI/ESD PHYSICAL     Size (Diameter x Height) 1.38 in x 1 1/8 in 35.1 mm x 28.7 mm Weight  (without cable) 6.1 oz 173 gm Mounting Through Hole Through Hole Mounting Thread 1/4-28 Male Not Applicable [5] Mounting Torque 2 to 5 ft-lb 2.7 to 6.8 N-m Sensing Element Ceramic Ceramic Sensing Geometry Shear Shear Housing Material Stainless Steel Stainless Steel Sealing Welded Hermetic Welded Hermetic Electrical Connector Armor Jacketed Cable Armor Jacketed Cable Electrical Connection Position Side Side Cable Length 10 ft 3.0 m Cable Type Polyurethane Polyurethane [6] SUPPLIED ACCESSORIES: Model 080B45 Thermal Boot (1) Model 081A73 Captive mounting bolt 1/4-28 x 1.34" (1) Model ICS-1 NIST-traceable single-axis amplitude response calibration from 600 cpm (10 Hz) to upper 5% frequency OPTIONAL VERSIONS LB - Low Bias Voltage Output Bias Voltage 6 to 8 VDC 6 to 8 VDC Excitation Voltage 12 to 28 VDC 12 to 28 VDC Measurement Range ± 7 g ± 69 m/s² M - Metric Mount Supplied Accessory : Model M081A73 Mounting Bolt M6 x 1.00 TO - Temperature Output Temperature Output Range +36 to +250 °F +2 to +121 °C Temperature Scale Factor 5.56 mV/°F + 32 +10 mV/°C Electrical Connector 3-Pin 3-Pin Electrical Connections (Red) Acceleration Output Acceleration Output Electrical Connections (Black) Ground Ground Electrical Connections (White) Temperature Output Temperature Output Electrical Connections (Green) Ground Ground All specifications are at room temperature unless otherwise specified. NOTES: [1] Typical. [2] Conversion Factor 1g = 9.81 m/s². [3] The high frequency tolerance is accurate within ±10% of the specified frequency. [4] Zero-based, least-squares, straight line method. [5] 1/4-28 has no equivalent in S.I. units. [6] Stainless steel armor jacket over twisted shielded pair. [7] See PCB Declaration of Conformance PS023 for details. [7]